testexam23 The Flydumps New Juniper JN0-360 practice tests helps the user to keep a check on their learning and understanding and improve for the Juniper https://www.leads4pass.com/jn0-360.html exam. Flydumps makes you pass your exam much easier.
QUESTION 63
Which two statements are correct about default MPLS behavior on Junos devices? (Choose two.)
A. The MPLS label is popped by the penultimate router.
B. The MPLS label is popped by the ultimate router.
C. The MPLS label is pushed by the ingress router.
D. The MPLS label is swapped by the ingress router.
Correct Answer: AC QUESTION 64
Which two statements regarding the MPLS label information base are correct? (Choose two.)
A. The MPLS label information base is stored in the inet.3 table.
B. The MPLS label information base is stored in the mpls.0 table.
C. The label information base is used by all LSRs to forward LSP traffic.
D. The label information base is used by transit LSRs to forward LSP traffic.
Correct Answer: BD
QUESTION 65
Which two statements are correct about RSVP path messages? (Choose two.)
A. They are sent by the egress router upstream.
B. They are sent by the ingress router downstream.
C. They are used to create an LSP.
D. They are used to reserve resources for an LSP.
Correct Answer: BC
QUESTION 66
Which two statements are correct regarding LDP-signaled VPLS instances? (Choose two.)
A. You must enable the Layer 2 VPN signaling NLRI.
B. You must configure the same VPLS identifier on all peers.
C. You must define a the same site-identifier value on all peers.
D. You must define all neighbors using their tunnel end-point IP addresses.
Correct Answer: BD
QUESTION 67
Which two statements are correct regarding LDP-signaled Layer 2 circuits? (Choose two.)
A. You must enable the Layer 2 VPN signaling NLRI.
B. You must configure the virtual circuit identifier.
C. You must specify the neighbor using the tunnel end-point IP address.
D. You must define a unique site-identifier value.
Correct Answer: BC
QUESTION 68
Which two statements are correct regarding BGP-signaled Layer 2 VPNs? (Choose two.)
A. You must enable the Layer 2 VPN signaling NLRI.
B. You must configure the virtual circuit identifier.
C. You must specify the neighbor using the tunnel end-point IP address.
D. You must define a unique site-identifier value.
Correct Answer: AD
QUESTION 69
Which two statements regarding VRF tables are correct? (Choose two.)
A. A PE router’s VRF table stores routes received from directly connected CE devices.
B. A PE router’s VRF table stores routes received from its IGP from remote PE devices.
C. A PE router’s VRF table stores routes received from MP-BGP from remote PE devices.
D. A PE router’s VRF table stores routes received from all P and PE devices within the same AS.
Correct Answer: AC QUESTION 70
You have been asked to implement routing policy on the PE devices in your AS and to ensure the correct customer routes are installed in the appropriate VRF tables.
Which component should be used as a match condition within your policy?
A. BGP communities
B. VLAN IDs
C. route distinguisher
D. circuit IDs
Correct Answer: A QUESTION 71
What is the purpose of a route target community in a Layer 3 VPN?
A. The community value is used to identify routes that should be imported by remote PEs.
B. The community value is used to determine valid remote devices when signaling a Layer 3 VPN.
C. The community value is used to identify the source of incoming routes.
D. The community value is used to determine transit devices when signaling a Layer 3 VPN.
Correct Answer: A QUESTION 72
You have been asked to deploy a Layer 2 VPN for a new customer.
What information will be present in the PE’s associated VPN forwarding table? (Choose three.)
A. the customer site ID
B. the route distinguisher
C. the interface encapsulation
D. the label base
E. the community name
Correct Answer: ACD QUESTION 73
You have an established Layer 3 VPN where you are using static routing between your PE and CE devices. You must advertise their directly connected subnet to remote PE devices.
Which two methods must you use? (Choose two.)
A. Use a site identifier.
B. Use the VRF table label.
C. Use a VRF export policy.
D. Use a route distinguisher.
Correct Answer: BC QUESTION 74
You have been asked to verify the state of an LDP-signaled Layer 2 circuit.
Which two commands would you use to verify the state of the connection? (Choose two.)
A. show mpls lsp
B. show l2circuit connections
C. show l2circuit statistics
D. show ldp database
Correct Answer: BD
QUESTION 75
What are two valid IPv6 addresses? (Choose two.)
A. 2bfc::02 :0:0:fe c:5c
B. 2bfc::2 ::fe c:5c
C. 2bfc:2 :0:0:fe c:5c
D. 2bfc:0:0:2 ::fe c:5c
Correct Answer: AD
QUESTION 76
Which new field is added to the IPv6 header when compared to IPv4?
A. version
B. fragment offset
C. checksum
D. flow label
Correct Answer: D
QUESTION 77
Which three are valid IPv6 extension headers? (Choose three.)
A. multicast header
B. authentication header
C. autoconfiguration options
D. fragment
E. hop-by-hop options
Correct Answer: BDE
QUESTION 78
What are two components of an IPv6 router advertisement message? (Choose two.)
A. DHCPv6 request
B. Layer 2 address of advertising router
C. duplicate address detection notification
D. link MTU
Correct Answer: BD
QUESTION 79
Which two statements are correct about neighbor discovery in IPv6? (Choose two.)
A. Neighbor discovery relies on ARP to find neighbors on a local link.
B. A neighbor is considered reachable when the neighboring device responds to a neighbor solicitation message.
C. A neighbor is considered reachable when the neighboring device responds to a router solicitation message.
D. Neighbor discovery does not use ARP to find neighbors on a local link.
Correct Answer: BD QUESTION 80
You want to configure an interface on your router to use an IPv6 global IP address. Which three methods accomplish this task? (Choose three.)
A. Use stateless autoconfiguration to assign only the 64 bit interface ID.
B. Use stateful autoconfiguration to assign only the 64 bit interface ID.
C. Use stateful autoconfiguration to assign the entire global IPv6 address.
D. Use a statically assigned global IPv6 address.
E. Use stateless autoconfiguration to assign the entire global IPv6 address
Correct Answer: ACD QUESTION 81
Which two support tunneling for non-IP protocols on Junos devices? (Choose two.)
A. ATM AAL2
B. GRE
C. IP-IP
D. ATM AAL1
Correct Answer: BC QUESTION 82
Which two support the tunneling of IP traffic on Junos devices? (Choose two.)
A. ATM AAL2
B. GRE
C. IP-IP
D. ATM AAL1
Correct Answer: BC QUESTION 83
Which two statements are true regarding GRE tunnels? (Choose two.)
A. GRE can be used to tunnel IP packets only.
B. A GRE tunnel can be applied only at the physical interface level.
C. GRE tunnels can be used to send nonroutable packets over a public IP network.
D. GRE tunnels can be used as backup links.
Correct Answer: CD QUESTION 84
Which two statements are true regarding GRE tunnel overhead? (Choose two.)
A. If the host sends a packet larger than the MTU, that packet must be dropped.
B. Packets are not dropped because the router clears the DF bit for GRE traffic by default.
C. Packets larger than the MTU are fragmented or dropped depending on the DF bit setting.
D. You can change the tunnel MTU to avoid packet fragmentation or drops.
Correct Answer: CD QUESTION 85
— Exhibit –user@router> show route 0/0 exact detail inet.0: 14 destinations, 14 routes (14 active, 0 holddown, 0 hidden)
0.0.0.0/0 (1 entry, 1 announced)
*Aggregate PreferencE. 130 Next hop typE. Router, Next hop index: Next-hop reference count: 4 Next hop: 172.30.25.1 via ge-0/0/1.100, selected StatE. Local AS: 65400 AgE. 1:03:46 Task: Aggregate Announcement bits (2): 0-KRT 2-OSPF AS path: I Flags: Generate Depth: 0 Active Contributing Routes (1): 10.0.0.0/16 proto BGP
— Exhibit —
Click the Exhibit button.
You are advertising the route in the exhibit to your OSPF neighbors.
What happens if the 10.0.0.0/16 route is unavailable?
A. The default route will remain active and will “blackhole” all traffic from your OSPF peers.
B. The default route will become unavailable and will no longer be advertised to your OSPF peers.
C. The default route will remain active and will continue to be advertised to your OSPF peers.
D. The default route will become unavailable and will continue to be advertised to your OSPF peers.
Correct Answer: B
QUESTION 86
— Exhibit –[edit policy-options]
user@router# show
policy-statement load-balance {
from {
route-filter 10.243.0.0/24 exact;
route-filter 10.224.1.0/24 exact;
}
then {
load-balance per-packet;
} } — Exhibit –Click the Exhibit button.
You have been asked to configure per-packet load balancing.
Referring to the exhibit, which configuration correctly applies the load-balancing policy?
A. [edit routing-options] user@router# show forwarding-options {
export load-balance;
}
B. [edit routing-options] user@router# show static {
export load-balance;
}
C. [edit routing-options]
user@router# show
forwarding-table {
export load-balance;
}
D. [edit routing-options] user@router# show routing-table {
export load-balance;
}
Correct Answer: C
QUESTION 87
— Exhibit –[edit]
user@router# show routing-options
rib-groups {
test {
import-rib [ walter.inet.0 nancy.inet.0 ];
} } — Exhibit –Click the Exhibit button.
Referring to the exhibit, what is the result of the RIB group configuration?
A. All routes from the walter.inet.0 and the nancy.inet.0 routing tables will be imported into the default master routing instance.
B. Routes from the walter.inet.0 routing table will be imported into the nancy.inet.0 routing table.
C. All routes will be shared between the walter.inet.0 and the nancy.inet.0 routing tables.
D. Routes from the nancy.inet.0 routing table will be imported into the walter.inet.0 routing table.
Correct Answer: B
QUESTION 88
— Exhibit –{master}[edit] user@router-RE0# run show task replication
Stateful Replication: Enabled
RE modE. Master
Protocol Synchronization Status
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
user@router-RE0# run show bgp summary | match 192.168.1.1
192.168.1.1 65056 288 327 0 2 1:05 Establ
{backup}[edit]
user@router-RE1# run show system switchover
Graceful switchover: On
Configuration databasE. Ready
Kernel databasE. Ready
Peer statE. Steady State
{backup}[edit]
user@router-RE1# run show bgp summary | find 192.168.1.1
192.168.1.1 65056 592 737 3778 2 1:33 Establ {backup}[edit]
user@router-RE1# run show bgp replication
Synchronization master: Session statE. Up, SincE. 6d 20:42:51 Flaps: 1, Last flap reason: Commit-sync error Protocol statE. Idle, SincE. 5d 19:41:52 Synchronization statE. Complete Number of peers waitinG. AckWait: 0, SoWait: 0, ScheduleD. 0 rsync walk at: inet.0 – , queued 0 Messages sent: Open 1, Establish 7415, Update 17, Error , Complete 48 Messages receiveD. Open 1, Request 1 wildcard 47 targeted, EstablishAck 2827, CompleteAck 4
— Exhibit —
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
A. An RE switchover is likely to result in BGP disruption, but no dataplane impact will be seen.
B. An RE switchover is likely to result in BGP disruption which will also effect the dataplane.
C. The system is not yet GRES ready, you need to wait for kernel synchronization to complete.
D. The system is NSR ready and a switchover should be hitless to the BGP control and data plane.
Correct Answer: D
QUESTION 89
— Exhibit —
{master}[edit]
user@router-RE0# run show task replication Stateful Replication: Enabled RE modE. Master
Protocol Synchronization Status
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
user@router-RE0# run show bgp summary | find 192.168.1.1
192.168.1.1 65056 0 0 11:14 Establ inet.0: 0/0/0/0 inet.2: 0/0/0/0 bgp.l3vpn.0: 0/0/0/0
…
{backup}[edit]
user@router-RE1# run show system switchover
Graceful switchover: On
Configuration databasE. Ready
Kernel databasE. Synchronizing
Peer statE. Steady State
{backup}[edit]
user@router-RE1# run show bgp summary | find 192.168.1.1
192.168.1.1 65056 306 581 0 7 7 Idle — Exhibit —
Click the Exhibit button.
You have been asked to determine if an NSR switchover will be hitless for a given BGP peer.
Referring to the exhibit, which statement is true?
A. The BGP session is idle on the backup RE indicating that the session will flap at switchover.
B. The task replication process has completed on the master indicating a hitless switchover can be expected.
C. The GRES synchronization process is underway and must complete before the protocol state can be checked.
D. The BGP session is idle on the backup RE which is normal; it toggles to established at mastership change.
Correct Answer: A
QUESTION 90
— Exhibit –user@R1> show configuration interfaces ge-1/1/0 unit 0 {
family inet {
address 10.100.1.1/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
priority 150;
accept-data;
track {
interface ge-1/0/0 { priority-cost 40; } } } } } }
user@R2> show configuration interfaces ge-1/1/0 unit 0 { family inet { address 10.100.1.2/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
accept-data;
}
}
} } — Exhibit —
Click the Exhibit button.
R1 and R2 are using VRRP for high availability.
Referring to the exhibit, which two statements are correct about the configuration? (Choose two.)
A. R2 is the backup router and will become the master router if ge-1/0/0 on R1 goes down.
B. R2 is the backup router and will remain the backup router if ge-1/0/0 on R1 goes down.
C. If R1 goes down, R2 will become the master and will relinquish mastership once R1 comes back online.
D. If R1 goes down, R2 will become the master and will remain the master once R1 comes back online.
Correct Answer: BC
QUESTION 91
— Exhibit –interfaces {
ge-1/0/3 {
unit 0 {
family inet {
address 192.168.1.1/30;
}
}
}
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.10.1/30;
}
}
}
fxp0 {
unit 0 {
family inet {
address 10.2.1.13/28;
}
}
}
lo0 {
unit 0 {
family inet {
address 10.100.1.1/32;
address 127.0.0.1/32;
}
}
} } protocols {
ospf {
area 0.0.0.0 {
interface ge-1/0/3.0;
interface ge-1/1/0.0;
}
} } — Exhibit —
Click the Exhibit button.
The router was just powered on.
Referring to the exhibit, what is the OSPF RID?
A. 192.168.1.1
B. 10.100.1.1
C. 127.0.0.1
D. 10.2.1.13
Correct Answer: B
QUESTION 92
— Exhibit –protocols {
isis {
level 1 disable;
interface ge-1/0/0.0 {
level 2 disable;
}
interface ge-1/1/0.0;
interface lo0.0;
} } — Exhibit —
Click the Exhibit button.
Referring to the exhibit, what is the resulting behavior on interface ge-1/0/0?
A. Level 1 is enabled.
B. Level 1 is disabled.
C. Level 2 is enabled.
D. Level 1 and Level 2 are disabled.
Correct Answer: A
QUESTION 93
— Exhibit –[edit] user@router# run show isis interface IS-IS interface database: Interface L CirID Level 1 DR Level 2 DR L1/L2 Metric ge-1/0/2.0 3 0x1 router.00 router.00 10/10 lo0.0 0 0x1 Passive Passive 0/0 — Exhibit —
Click the Exhibit button.
Referring to the exhibit, which two statements are true regarding the GE interface? (Choose two.)
A. It operates at both Level 1 and Level 2.
B. It operates at Level 3, which supports hierarchical backbone areas.
C. The local router is the IS-IS designated intermediate system at all levels.
D. The local router is the IS-IS designated router at all levels.
Correct Answer: AC
QUESTION 94
— Exhibit –user@R2> show protocols {
isis {
export leak;
interface ge-1/1/0.0;
interface ge-1/1/1.0 {
level 1 disable;
}
interface lo0.0;
} } policy-options {
policy-statement leak {
term 1 {
from level 1;
to level 2;
then accept;
}
} } — Exhibit —
Click the Exhibit button.
We know that the real Juniper JN0-360 examinations wouldn’t repeat the same set of questions all the time. Microsoft certification examinations are strict and focus is often kept on updated technology trends. The Juniper https://www.leads4pass.com/jn0-360.html practice test prepared by the experts will help to condition your mind to quickly grasp what you could be facing in the real Juniper JN0-360 certification examination.